 |
|
|
|
|
|
 |
|
 |
|
 |
|
 |
|
 |
|
|
30% Larger carbide tips, than conventional blades.
|
|
 |
|
 |
|
 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Use on sliding table saws.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Universal application for cutting along and across the grain in solid wood and board material. Grind=ATB
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The best solution where one blade is needed in multiple cutting applications. Grind=4ATB+R
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For extra thin cutting of expensive material. Grind=ATB & TC
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For the best sizing and finishing cuts in plywood, veneer, plastic laminate board material, table saws, and verticle panel saws. Grind= Triple Chip
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For ripping and cross cutting of solid wood and board materials on table saws, special sawing machines with chip limiter to reduce kickbacks. Grind=ATB
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For use on building sites, designed to cut wood with nails, concrete residues, tubes, and similiar wood inclusions. Grind=TC
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For ripping and cross-cutting of solid wood and board materials on table saws, special sawing machines
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For smooth cuts on wood moldings and the least possible grabbing of materials. Grind=4ATB+R
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For perfect cutting quality in melamine-faced board material on both sides up to 30mm cutting height. For use on table saws and vertical panel sizing saws. Grind=V-Hollow
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The cleanest cutting rip saw on the market, for all glue line applications. Grind=TC
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Designed to be used in portable machines. Grind=ATB & TC
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Best choice for chip free top and bottom, cuts in double sided material such as melamine, and both high and low pressure laminates. Grind=D-TC neg.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For fine cuts in laminated board material on both sides with melamine, formica, veneer, etc. Used on table saws with a scoring unit, vertical panel saw, radial arm saws, mitre and chop saw. Extra hard sub-micron grain for linger life. Grind=ATB neg hook
|
|
|
|
|
|
|
|
|
